3-trode best shaft+balls feeling config?

[Jack Frost]

I have corona w/u amp, mid ring and test tubular.

I was thinking to get the least sensation in the corona and most on the shaft and balls would be this:

Channel A: Negative terminal on balls, Positive on Mid-ring
Channel B: Positive Terminal on corona, Negative Taped off.

I won't have a chance to try this for a day or so, so Im wondering if anyone has thoughts.

The idea is, positive flows from corona and mid-ring to the balls.

I tried midring being negative and positive on balls and corona and thats way too much stim on corona cuz I think the distance from midring to corona is so short :(

[ednc8818]

I have no idea what you are talking about. Could you simplify please?
ednc8818

[Jack Frost]

Heh sorry.

Here is my diagram:

8===>

The 8 is the balls, the === is the shaft the > is the head.

On the P.E.S. power box are two channels, A and B.

Each channel has to be a complete electrical circuit. So, on channel A you have to have both - and + connected to your body to have the electrons flow from the + positive terminal to the - negative terminal.

The idea in a 3 electrode configuration is you use the - and + from channel A and only one either - or + from channel B.

If you use Channel A's -+ and Channel B's + then you effectively have two + terminals and only one - terminal.

The question is, since the power is shared between the two terminals is -++ the same as --+ or does the number of negative and positive terminals not change anything?

I want to reduce the amount of electrons flowing to the head of the penis. so i was thinking of putting the + on the balls, and - negative on both the shaft (midring) and - negative on the corona head.

This means the + positive electrons will mostly flow to the midring, and only a few that shoot past will make it to the corona.

Alternatively, you could go + and + on midring and head, then - on balls.

This means lots of electrons will be flowing from both the head then double up at the midring and both to the balls.


This is the theory at least. I think it doesn't really hold very important only because when you use two channels on a PES box, I think each channel effectively has 1/2 power.

I think you gotta be an electrical engineer to figure this out :P

Maybe two PES boxes would be more effective to controling the power in two different areas better.

[ajelec]

Jack-
You may be only partially correct in your initial assumption. Electronic theory assumes transfer of electrons from - to +. Practical automotive theory assumes that the flow is from + to -. It may take some clinical research to determine the actual direction when applied to the human body.
Please keep us informed with your results.
AJ

[Jack Frost]

Jack-
You may be only partially correct in your initial assumption. Electronic theory assumes transfer of electrons from - to +. Practical automotive theory assumes that the flow is from + to -. It may take some clinical research to determine the actual direction when applied to the human body.
Please keep us informed with your results.
AJ


The result so far has been that a 3 electrode configuration doesn't work for me.

I'll have to try it again, but it's just been annoying so far. Everyone says 3 is better than 2, but I can't get it right.

Playing with them, I do seem to get more stim to the balls versus the head or vice versa, but it just doesn't feel good IMHO.

I've HFO'd a dozen times with the corona + testicular tube though. Simple configuration.

I'll try the 3 trode setup again though for sure now that I've got the 2 trode setup down pat.

The only thing that I think could make this better is prostate stim + testicular + corona. I really want to try that!

I gotta go order that thing :P

[sflapmpr]

PLEASE NOTE THAT I HAVE AN EROSTEK 312 SO THIS MAY NOT APPLY TO THE PES UNIT.

The Erostek has 2 channels. In order for each channel to work the electrical loop for each channel must complete. To do "tri-phase" (3 electrodes) on an Erostek with PES electrodes (the ones I use) I use the + of channel A on one trode, the + of channel b on another trode and then join the commons from channels A & B (on my unit it's the wires with the white stripes) and place them on a 3rd electrode. That way I get to control the intensity very well on 2 of the trodes while using the common leads combined on a trode that is less critical.

I usually like to use the testicular tubular trode on one channel the corona stimulator on the other channel and a sparkler used as a cockring on the commons. I am then able to increase the level to the testicular trode which is usually much lower in intensity than the corona trode.